
Bookstore

Source: Ansys
You can control three mechanisms in ANSYS Workbench that operate in a parallelized manner:
-
Remote Solve Manager Design Point updates. Refer to RSM Configuration.
-
Parallel Part meshing: > >
-
Individual mesh methods (MultiZone Quad/Tri, Patch Independent Tetra, and MultiZone only): > >
For the most efficient use of machine resources, it is important that the running processes do not over-saturate the processing cores or the available memory. You must allocate processing cores to each of these mechanisms in a way that provides the most benefit for your workflow. When parallel part meshing is invoked with the default number of CPUs, it automatically uses the cores of all available CPUs with the inherent limitation of 2 gigabytes per CPU core.
Parallel Part Meshing Best Practices
Best practices include:
-
Know how many physical processing cores are available.
-
If you are using Remote Solve Manager (RSM), meshing is done serially. This option cannot be overridden.
-
For non-RSM Design Point updates, meshing is done serially by default. You can override this option by setting the option Number of CPUs for Parallel Part Meshing explicitly under .
-
If you are using more than one processor for individual meshing methods, be sure to set a balance between the two meshing options if you are using methods that support the Number of CPUs for Meshing Methods option (MultiZone Quad/Tri, Patch Independent Tetra, and MultiZone). They should be set to an explicit value greater than 0.
For example, if you are using an 8 core system, setting Number of CPUs for Parallel Part Meshing to 3 and Number of CPUs for Mesh Methods to 3 will provide a good balance. If the mesh methods that you typically use support the Number of CPUs for Meshing Methods option, setting the Number of CPUs for Parallel Part Meshing to 2 and the Number of CPUs for Meshing Methods to 4 or 5 may potentially provide more benefit.
-
If you are using parallel part meshing only, you can set the Number of CPUs for Parallel Part Meshing to 0. In such cases, the software uses as many cores as possible.
-
For Parallel Part meshing we recommend turning off hyper-threading as this may lead to degradation of parallel performance.
-
Note that Parallel Part meshing does not support the following mesh controls:
-
Assembly meshing
-
Contact Sizing
-
Fracture
-
Mesh Match via Symmetry
-
Morph Service/Morphing
-
Pinch
-
Post Connection
-
Post-Inflation
-
Preview Surface Mesh/Preview Inflation
-
Retry
-
Refinement
-
In this tutorial, you will learn how to do a parallel mesh using Ansys Meshing. In this video we show the configuration to customize the number of cores of your processor.

Ansys Fluent Tutorial | Heatsink
In this tutorial, you will learn how to simulate a Heatsink using Ansys Fluent. In this first video, you will see how to create the geometry and the mesh using DesignModeler, Ansys Meshing and Ansys Fluent.

Ansys Meshing | Inflation
You can set the Use Automatic Inflation control so that inflation boundaries are selected automatically depending on whether or not they are members of Named Selections groups.
Related Articles
Ansys Fluent Tutorial | Heatsink
In this tutorial, you will learn how to simulate a Heatsink using Ansys Fluent. In this first video, you will see how to create the geometry and the mesh using DesignModeler, Ansys Meshing and Ansys Fluent.
Ansys Meshing | Inflation
You can set the Use Automatic Inflation control so that inflation boundaries are selected automatically depending on whether or not they are members of Named Selections groups.
Ansys Meshing – Keyframe Animation
You can make animations based on keyframes. Keyframes define the start and endpoints of each section of animation.
Ansys Meshing – Match Control
In this tutorial, you will learn how to use the Match Control tool in Ansys Meshing. Match Control allows duplicating the mesh in a body. We have two option Match Control Cyclic and Arbitrary.
Ansys Meshing – Body of Influence
The Body of Influence option is available in the Type field if you selected a body and Use Adaptive Sizing is set to No. Using this option, you can set one body as a source of another body
Ansys Meshing – Sphere of Influence
The Sphere of Influence option is available in the Type field after you select an entity such as a body, face, edge, or vertex.
Stay Up to Date With The Latest News & Updates
Help us keep growing
CFD.NINJA is financed with its own resources, if you want to support us we will be grateful.
Join Our Newsletter
Subscribe to receive emails with detailed information related to the CFD.
Follow Us
Subscribe to our social networks to receive notifications about our new tutorials