
Bookstore

Source: Ansys
The feature is a tool used to define a symmetry model. The feature takes either all the bodies or selected bodies of the model as input and accepts up to three symmetry planes. You can choose either full or partial models to work with. If a full model is used, the selected symmetry planes will slice off the model and only a portion of the model will be retained. The valid body types for this feature are surface and solid.
During the model transfer from ANSYS DesignModeler to the Mechanical application, the faces and edges coincident to the symmetry planes are grouped into a named selection if the Export Symmetry property is set to Yes. Additionally, each symmetry plane chosen in the Symmetry feature will be transferred to the Mechanical application as a coordinate system.
It is recommended that you do not change the symmetry plane selection after a model has been transferred to the Mechanical application. The Mechanical application will not delete the previous symmetry planes during updating. A similar note applies when using the Named Selection feature.
The following properties allow you to control the behavior of the feature:
-
Number of Planes: This property defines how many symmetry planes are used in the feature.
-
Symmetry Plane 1: First symmetry plane selection.
-
Symmetry Plane 2: Second symmetry plane selection.
-
Symmetry Plane 3: Third symmetry plane selection.
-
Model Type: This property specifies either Full Model or Partial Model as input.
Full Model: ANSYS DesignModeler will use the chosen symmetry planes to cut the full model, leaving only the symmetrical portion. For each symmetry plane, material on the positive side of the plane (that is, the +Z direction) is kept, while material on the negative side is cut away. Partial Model: Since the model has already been reduced to its symmetrical portion, there is no model change after the Symmetry feature is generated. However when the model is transferred from ANSYS DesignModeler to the Mechanical application, the faces and edges coincident with the symmetry planes will be identified automatically and put into a named selection if the Export Symmetry property is Yes. -
Target Bodies: This property specifies whether all of the bodies or only selected bodies of the model will be enclosed. The default is All Bodies.
-
Bodies: If Target Bodies is set to Selected Bodies, then this property becomes available. It is an Apply/Cancel button property that facilitates selection of the target bodies.
-
Export Symmetry: Determines whether symmetry plane data is transferred downstream to the Mechanical application. The default is Yes.
In this tutorial you will learn to to use Symmetry tool in Ansys DesignModeler.

Ansys Fluent Tutorial | Heatsink
In this tutorial, you will learn how to simulate a Heatsink using Ansys Fluent. In this first video, you will see how to create the geometry and the mesh using DesignModeler, Ansys Meshing and Ansys Fluent.

Ansys DesignModeler – Tetrakaidecahedron
A tetradecahedron is a polyhedron with 14 faces. There are numerous topologically distinct forms of a tetradecahedron, with many constructible entirely with regular polygon faces.
Related Articles
Ansys DesignModeler – Tetrakaidecahedron
A tetradecahedron is a polyhedron with 14 faces. There are numerous topologically distinct forms of a tetradecahedron, with many constructible entirely with regular polygon faces.
Import from Autodesk Inventor to Ansys DesignModeler
Autodesk Inventor is a comprehensive and flexible set of software for 3D mechanical design, simulation, tooling creation, and design communication.
Ansys DesignModeler – Ansys Beta Options (Solid Extension)
By default, System Coupling’s beta features are not activated. When beta features are activated, the corresponding settings are added to the data model and are available for use.
Ansys DesignModeler – Thin/Surface
The Thin/Surface feature allows you to convert solids into thin solids or surfaces. The feature can operate on both active and frozen bodies. Typically, you will select the faces to remove, and then specify a face offset that is greater than or equal to zero (>=0).
Ansys DesignModeler – Import from SOLIDWORKS to DesignModeler
Some import types (ACIS and AutoCAD) allow you to specify the units of the imported model. Before clicking Generate, you may be able to change the model units from the Details View, depending on the type of import. Note that some model types store their units, so no Model Units property will appear when importing them.
Ansys DesignModeler – Import from Autodesk Inventor to ANSYS Design Modeler directly
Use the Open command to open files created in any supported format. Use the Save As command to export parts, assemblies, drawing sheets, and 3D markups to formats read by other applications. Your license type determines which of these actions are supported.
Stay Up to Date With The Latest News & Updates
Help us keep growing
CFD.NINJA is financed with its own resources, if you want to support us we will be grateful.
Join Our Newsletter
Subscribe to receive emails with detailed information related to the CFD.
Follow Us
Subscribe to our social networks to receive notifications about our new tutorials